The furniture made by traditional craftsmanship has extremely high artistic quality, ornamental quality, pure solid wood, and hand-carved furniture. Only in this way can it highlight the unique charm and extraordinary value of craft furniture. Superb craftsmanship gives the furniture its eternal vitality. Have you ever tried to make your own furniture? Today, the Plantini Belt took everyone to understand the six steps in the production of wooden furniture .
first step
Design drawings, ingredient preparation, quantity and types of wood, etc., but also to check the hand-over of the wood, the choice of good wood is a good basic furniture.
Second step
The positioning of the sawing material and the positioning of the drawing line are the parts processed by planing, jigsaw, etc. According to the size of the product, according to the drawings, the line drawing of the parts is well positioned, such as the position of the snoring. The location of the slot must be precise.
Second step
Punching, ramming structure, according to the product specifications, the size of the product, according to the positioning of the sawing material, drawing lines, with a hole punching machine, using a saw to cut the board, with slot machine slot. To make a hole in the wood, you must first draw a line on the wood and decide on where to open the hole. Due to the large size of woodworking, it can be reduced; if it is small, it cannot be increased. When using a saw to pull, pay special attention to reasonable line (termed "eat line", "let the line", the meaning of the two are different, used for different parts), in order to ensure that the mouth and eyes have repair, correction More than expected. In fact, it is necessary to carry out many careful amendments to the mouth and eyes to ensure that the connection between the eyelids and the eyes can be matched. After the assembly, the wood materials are perpendicular to each other, and the joints at the mouth are tightly jointed.
the fourth step
To make a round, put through the production, according to product design, to do round shape, using a round machine, the four corners of the wood round. The rounding process should be symmetrical, smooth, smooth, no missing corners, knife marks. Processing surface frames, panels, door frames, door panels and other parts, all have four wooden frames, two long and out of the box called "big side", two short eyes called "edge wipe." Join the frame with the corners of the sides and edges, and then hit the plate on each side. Utilize the space of the trough, make the shrinking wood not to destroy the panel, or make the panel warped, and reasonably solve various problems caused by thermal expansion and contraction of wood.
the fifth step
According to the specification of various bending materials, according to the specification of various bending materials, the bending materials to be processed are fixed together, and it must be ensured to be consistent, positioned, and machined with square grooves.
Step 6
The product is assembled at this stage of product assembly. The requirements are that the part and the panel should be at 90 degrees, the interface is smooth and smooth; the four feet are not inclined, the diagonal should be 90 degrees, and the four feet should be flat as glass. When the product is assembled, there is an orderly process. First, the parts are assembled, the lower frame is assembled, and the entire assembly is performed. The tools used are wooden hammers, fixtures, etc.
Component assembly
According to the product's structural assembly drawing, the processed parts are combined into a relatively independent structural component unit. The "combination" in this process is different from the "combination" in the modern furniture assembly. Instead of directly combining the components into products, the parts are finely machined and combined with zeros and parts. The first part of the combination is to remove the blemishes, reduce blemishes, and look for types of coarse-grained components, and check whether the rakes are of the right size, tightness, skew, or angling. If you find it inappropriate, you must repair it in time.
Whole assembly
Assembly is the combination of furniture accessories into a complete piece of furniture, the difficulty of the combination is quite large, the assembly requires a level, clean ground. This is a necessary condition to ensure the quality of furniture assembly. There are two reasons for this. First, even if the furniture is correctly assembled, the unevenness of the ground will lead to a "walking fan" due to the weight of the furniture. If you assemble on uneven ground, it is not easy to tell whether the furniture is installed. The second is that hardwood furniture is very heavy and placed on uneven ground. The force on the legs is uneven, which can easily cause deformation of the furniture. When assembling, various parts are prepared, placed in order, and assembled in order. The order of assembly varies from furniture to furniture. As cabinets and the like, it is necessary to first assemble the cabinet door and the two side mountains first, and after measurement, there is no dimensional error, and after the drying is completed, the cabinet can be assembled. In the process of assembly, we must master the tightness of the drawer and the interface, or tightly crack the cabinet until it cracks. If it is loose, the furniture will be twisted.
The above is a simple understanding of the production of wooden furniture . It takes a lot of effort to learn how to produce satisfactory furniture .
related articles
Custom furniture production process Custom furniture production six steps
How sofas are made Omido analyzes how sofas are made
Stainless Steel Tea Strainer,Teapot With Strainer,Loose Leaf Tea Strainer,Plastic Tea Strainer
YANGJIANG VOSSEN INDUSTRY AND TRADE CO.,LTD , https://www.cnvossen.com