Many of my friends are busy with how to decorate their homes. So what about the decoration and punching knowledge of our renovated house? If friends want to know, let’s take a look at the content of this article in our decoration home network. How to introduce it, our decoration and punching is to first figure out where to decorate the hole in the new house, and what is the mastering skill of this decoration punching, as well as the precautions for decoration punching.
First, the location of the decoration hole
The places where the kitchen needs to be punched are generally the two places, the smoke outlet and the cabinet.
1. It is best to pay attention to the flue hole when punching the exhaust port, so as to avoid inconvenience when installing the pipe.
2. When the flue hole is in the opening, the lower edge cannot be on the top of the hanging cabinet, otherwise the gap in the hanging cabinet may smoke, which leads to the flue smell.
3, the flue hole is best not to be blocked by the gas pipe, this can prevent the smoke from being squeezed when installing the flue.
The living room is designed to be perforated, and the air conditioner is installed and perforated.
1. Precautions for lamp punching
2. At the time of decoration, many owners will choose “water pipes to go to the topâ€. When punching the lights at the top of the living room, be careful not to break the water pipes. At the same time, avoid the top cement holes to avoid affecting the quality of the house. .
3, air conditioning installation punching precautions
Second, the correct way to decorate the hole
1. In order to ensure the safety of the construction, it is not recommended for the owner to do it himself. The wall punching is generally done by a professional master. Unprofessional technicians may not only cause damage to the wall, but may also cause accidents, posing a threat to the interests of the owner. When calculating the drilling cost, it is necessary to communicate with the construction party for various details and strengthen supervision so as not to be regrettable.
2. The corresponding punching tools should be prepared before construction. Generally speaking, the master will bring it. You should choose the corresponding punching tool according to the material of the wall. If it is a red brick wall, you can directly use cement steel nails. If it is a concrete wall, you must first punch it with a hammer and then use a wooden wedge. Knock into the hole and nail the wooden strip. Next, fix the shelf on the wooden note. Do not use other wooden boards and wooden notes to flatten and then nail the decorative panel to paint.
3. Punching looks very simple, in fact, it is a technical activity. When you are punching, don't be too hasty. In the process of punching, it should be pulled back and forth to prevent dry powder stuck. In addition, the drill bit must be stable when punching the wall. Do not shake it to the left, because you shake it together, which is equivalent to increasing the friction of the drill bit.
Third, the decoration hole punching matters
1. First of all, when we punch the air conditioner, we need to find a suitable position for the hole. We must avoid the load-bearing wall. The load-bearing wall cannot be touched. Otherwise, there may be certain safety hazards.
2. If it is necessary to punch holes on the beam, it must be carried out on both sides of the beam, otherwise it will easily cause uneven stress on the beam body, which will lead to the safety of the building, so the position of the hole must be on both sides. The middle part is carried out.
3. If the other side of the air conditioner is outdoor, then we must consider the inclination of the hole. Make sure that the outdoor position is lower than the indoor position, so that the rain will not be poured into the room.
4. The size of the air-conditioning punching must be larger than that of the copper pipe, because after the hole is punched, the copper pipe should be equipped with a washer, so it is necessary to ensure that the copper pipe can smoothly pass through the hole.
5. When we purchase the air conditioning tube, we should consider the installation position of the air conditioner indoor unit. Because the air conditioner punching is generally the responsibility of the manufacturer, we need to buy the air conditioner at the beginning of the decoration. Kong will not affect the interior decoration effect of the home.
The introductions that the above friends have seen are the correct position of our decoration punching in the room, friends should not make mistakes, and there are other techniques that our friends should learn when they are punctured. Mastered, and there are a lot of precautions in our decoration and punching. There are a lot of decoration information in our decoration home network, and friends can pay attention to it at any time.
More related wonderful reading:
Tile punching content introduction, tile buying skills introduction
Wall punching precautions wall punching methods and tools
Bearing wall can be punched?
Wall Punching Precautions Wall Punching Skills Introduction
How to choose the location of air conditioning punching? Air conditioning punching precautions
Metal Mesh fence structure is weaved or welded by low carbon steel wire, metal steel tube, or expended mesh with pvc coacted and fixed by the linking accessories and steel pipe. The Fence Netting has the feature of high strength, good steel natural capacity, wonderful shape, wild field of vision, The metal fence is very popular with projects of highway, railway, airport and other residential area.
Fence Netting
Fence Netting, Deer Fence, Welded Wire Fence,Windbreak Fence, Airport Fence,Steel Fibric Fence
Hebei TongChan Imp.&Exp.Co., Ltd. , https://www.tongchanmesh.com